Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
This post following next relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is totally compelling. Have a go and make your own findings.
Setting up a bathtub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, and often, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably challenging project. If the old tub is conveniently obtainable, the job can move immediately; if you need to open up a wall to get rid of the old bathtub and also place the new bathtub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will require a helper to leave the old tub and also embeded in the new one. See to it you have actually qualified yourself for the job as well as fit trying it. As opposed to hiring a professional to take over a halfway-completed task, it is better to think about employing one before you begin. Possibilities are you might need a professional plumber to make tube connections.
This article will certainly assist you set up a new tub in your shower room if you have actually currently bought a brand-new bathtub and don't require to alter the plan of your previous supply of water pipes.
Your tools and also material checklist should consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is disconnect the water system. After doing so, turn on the faucets to drain any water remaining in the system. The process of eliminating the existing taps can be quite troublesome because of the restricted gain access to that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Before proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Safeguard the faucet in position with the maker given backnut. When the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The former kind should be attached to the tap finishes initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Using both wood boards under its feet, place the bathtub in the required position. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four little factors.
The next goal is to ensure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bath tub till the spirit level reads level.
To install taps, fit all-time low of the furthest flexible tap connector to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the supply of water and also check all joints as well as new pipework for leakages and also tighten them if essential. Load the bathtub and additionally examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the producer's user's manual. Tiling as well as securing around the tub needs to wait till the tub has actually been utilized at the very least when as this will certainly settle it into its final placement.
Getting ready for the Installment
To start with, the sustaining structure provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the adaptable tap ports to the bottom of both faucets utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you use all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its final position.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to break a stiff seal, causing the water to permeate the wall surface between the bath as well as the tiling, resulting in problems with dampness as well as feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to blend in your components and also installations. They are marketed in tubes and also cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always load the bathtub with water prior to sealing, to permit the movement experienced when the tub remains in usage. The sealant can split rather early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the tiles making use of waterproof or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that entry on How to Install a Bathtub while scouting around the search engines. Are you aware of somebody else who is interested in A Step-by-Step Guide to Installing a Bathtub? Feel free to promote it. Thank you for taking the time to read it.
Schedule A Service Report this page